- How long does a 12ax7 tube last?
- Why do tube amps sound better loud?
- Are tube amps dangerous?
- Is a tube amp better?
- Is it bad to leave a tube amp on for a long time?
- Is it bad to leave a tube amp in the cold?
- How much does it cost to replace tubes in an amp?
- How often should I change preamp tubes?
- Should I turn off my tube amp?
- How long should I let my tube amp warm up?
- Why does my tube amp crackle?
- Should preamp tubes be matched?
- How do you know if your tubes are matched?
- How do you tell if a tube in an amp is bad?
- How long do amp tubes last?
- Why do tube amplifiers sound better?
- Can you touch amp tubes?
- What can you not do with a tube amp?
- Are amp tubes supposed to glow?
- Do power tubes have to be matched?
- Why are tube amps so expensive?
How long does a 12ax7 tube last?
about 10,000 hoursSmall signal tubes like a 12AX7 or 6922 will work well on average for about 10,000 hours..
Why do tube amps sound better loud?
Because valve/tube amps have an output transformer causes the amp to have a ‘high output impedance’. … This is a form of distortion, as the speaker is not following exactly the signal the amplifier is feeding to the speaker. This is the only reason a tube amp ‘can’ sound louder than a elderly transistor amp design.
Are tube amps dangerous?
WARNING: A tube amplifier chassis contains lethal high voltage even when unplugged–sometimes over 700 volts AC and 500 volts DC. Never touch the amplifier chassis with one hand while probing with the other hand because a lethal shock can run between your arms and stop your heart. …
Is a tube amp better?
Tube amplifiers sound better because of the euphonic distortions they add to the music, as well as plenty of other reasons I’ll cover below. … We use tubes simply because they make the music we create sound better: smoother, warmer and cleaner. Ditto for guitar amplifiers used in creating music.
Is it bad to leave a tube amp on for a long time?
Don’t leave your tube amp on standby for too long, it can cause damage! It’s all about the capacitors!
Is it bad to leave a tube amp in the cold?
Tubes are not harmed by cold weather as long as they are allowed to warm up and cool off GRADUALLY. That means when you bring your amp inside from five hours in the back of a sub-zero truck you need to let it warm up to room temperature before applying power (this is basically true of all electronic equipment).
How much does it cost to replace tubes in an amp?
EL84 aren’t much more. If you just get run of the mill stuff it will be cheap. Once you start looking into NOS tubes, etc, you can expect to pay $25-200 per tube in some cases.
How often should I change preamp tubes?
You should replace them when they are dead. *There is no set rule for how long they last, but in general, they last longer than power tubes. *Maybe twice as long or better life expectancy for power tubes. *They are also self-biasing of course, so don’t be afraid to change them yourself.
Should I turn off my tube amp?
If you’d rather replace your tubes than your entire amp, turn it off when you’re done using it. It’s better for your tubes, anyway! Turning your amp off is also the safest choice. As heat builds up over long periods of time, not only does your amp suffer, things can get dangerous.
How long should I let my tube amp warm up?
20 to 30 minutesAs a rule of thumb, your tube amp needs to be warmed up for 20 to 30 minutes at least before you can start playing your guitar.
Why does my tube amp crackle?
A poor tube connection may be the source of the crackling noise you’re hearing. Sometimes, gently pulling on the tubes can help re-seat them better and give them a better connection, thus fixing your problem. The crackling can also be caused by a bad tube, in which case you’ll need to try swapping them out.
Should preamp tubes be matched?
Preamp tubes do not need to be matched, only power tubes. If one of the preamp tubes you’re replacing is the phase inverter, then that should be balanced.
How do you know if your tubes are matched?
Normally only output (large) tubes are matched. If input (small) tubes are not marked “left” and “right” etc., it won’t matter. The output tubes will be marked as pairs in some fashion. Before you rip the boxes open, look for rubber bands holding pairs (or quads) together.
How do you tell if a tube in an amp is bad?
Crackling, squeals and feedback, excessive noise and muddiness or low output are all evidence of tube problems. Power tubes. The two main symptoms of a power tube problem are a blown fuse or a tube that begins to glow cherry red. Either are typically indicative of a power tube failure.
How long do amp tubes last?
You can expect a conventional amplifier tube to have a service life ranging up to 10,000 hours. Tubes with military specifications are built to last up to 100,000 hours.
Why do tube amplifiers sound better?
Tubes, like analog recordings, have a more full-bodied sound than transistor gear. There’s a “roundness” to tube sound that solid-state gear never equals. Tubes are less forgiving about mismatches, so to get the best out of a tube amp it must be used with just the right speaker.
Can you touch amp tubes?
Make sure you power down the amp, unplug it, and give it adequate time to cool down before you touch anything — tubes can get really hot.
What can you not do with a tube amp?
Never, never, never run the amp with no speaker plugged in. This can cause major damage. Do not flip the power switch off, then back on rapidly. This can cause power supply damage.
Are amp tubes supposed to glow?
A: That blue glow is just a side effect of a power tube — a fluorescent glow in the blue spectrum. The tube is fine! It actually indicates that the vacuum inside the tube is very good, which is what allows this phenomenon to occur. It will not have any effect on the performance or tone of the amp.
Do power tubes have to be matched?
Power tubes require matching because the way they amplify signal can create exceptionally bad sound if they are poorly matched, but pre-amp tubes generally aren’t used this way and so matching them is unnecessary.
Why are tube amps so expensive?
Tube amps are expensive because they adopt pre and power tubes as their primary amplification source. Each tube costs roughly $50 and can have up to 4 of them within a single unit. Secondly, these amps have more expensive components, larger cases, and more complex circuitry than solid-state amps.